Classifieds

Located in Michigan, budget 10k for the right condition. Would be willing to include my 1969 27ft commander hardtop as part of a trade if desired. Approx 150 hours on rebuilt 327Q. Photos included below and more information available upon request. Let me know what you have!

Thanks, Matt

31 Express - 1st choice would have the - cockpit enclosed (w/sliding door), no upper helm. Don't mind some to-do items but not looking for a heavy project boat. As OEM as possible but some modern tasteful upgrades are fine (i.e.. Generator, Diesel swap, updated upholstery etc.). Fresh water would is preferred. Lake Champlain is our current local waters, would be great to find a nice 31 on the Great Lakes, inland Northeast area.

If your thinking of selling your 31 or know of a clean 31 Express for sell, please reach out to me. Looking at all the common boat sites, including FB Marketplace.

Thanks!

Gregg

greggnvt@yahoo.com

Anyone know a source for a replacement hatch cover for the forward deck?

Thank you.

Hey all, I'm in Michigan and looking for a half decent trailer to put my 27 on. I want something road worthy but I don't care if it's pretty and I'm not afraid of re-wiring

In search of owner I have a copy of the first page of the invoice for the Hull # FFA-42-0001F dated 07-02-75. And an original brochure from 1975. Contact me if of interest. email legrandfromage@comcast.net

Hello all….:: looking for a cockpit step. Anyone have one. jogeo59@gmail.com. George Holzmacher

Hi all

I’m looking for the Flybridge windshield side pieces!! They’re are two. They are curved pieces. These are about 12 inches to maybe 15 inches high. I’ve gotten scammers saying Inhave these!! Pay me before I show you them. Etc. anyone have them or Know whom to call? Part out? They are all NOT the same.

Thanks

Rob s

I am looking for the hardware that goes to the folding handrails. I have the smaller rails (not 2-3/8” wide). I need the folding wood sections, folding bracket, male and female receiver opposite the hinge.

I would also take the 2-3/8” hardware if it were full sets for port and starboard sides.

Message me if you have any leads.

Thank you,

Dr Greg

Hi - in search of replacement dials for a 1968 Commander 31. Seeking triple style ampres, oil pressure and temp but would consider anything in reasonable condition, based in UK. Thanks in advance for any offers

Dear Commander Community,

First, thank you for being the stewards of these fine boats.

We are interested in pursuing the purchase of a 55 or 60ft. Commander.

We would prefer a later production 55 with the enclosed aft deck but would consider all 55 or 60 foot commanders.

We currently own and operate a 1972 Huckins 53 Corinthian which we love but we still lust for the larger Commanders.

Please feel free to text or call us at (616) 914-9303.

Looking for a 34-38’ Chris Craft commander or similar. Located on the Long Island sound. Willing to travel for the right boat.

Must have transom door, bunks + V birth

Diesels preferred

860-576-0909

Thank you!

I need the circuit diagram from the ~1966 service manual for my Kohler Generator. Bottle of scotch for help on this one. I'm trying to upgrade the old controller with a Deep Blue digital controller, but my service tech needs the original circuit diagram. If you have access to a manual I can buy/copy/borrow, please call or text me.

Thanks,

Mike

C: 231 620 4449

I purchased this boat last fall and it has nothing for a captains chair. What would you recommend? Does anyone have anything for sale or know where I could find something?

Thank you,

This is the jetson style chrome anchor/steaming light that sits atop the mast on Commanders around 1977.

If so, respond back or call me. Thanks!

Hap Carlson

Port Washington, WI

414-333-8569

Looking for an early 1970's. Contact Bill Boyle wgb@axiaappraisal.com

773-523-0255

Commander Dash panel

If you have a set please let me know!

Thanks!

Jake

Jpav8r@gmail.com

419-357-3730

photos.app.goo.gl

After jumping through hoops with the PA Fish and Boat Commission, I was finally able to get the 360 Commander we purchased titled and registered in PA; to find out they registered it as a 1982 Chris Craft verse a 1983 which was on the previous Title from owner/Michigan; after reaching out to my State Rep and in turn speaking with the PA Fish and Boat; they explained that the Hull ID should be 12 numbers with the last dictating the year of the boat; they further stated they would not change it; before I go back to the notary and take up further issue I wanted to see if anyone had additional information.

Long ago, I saw an old Chris Craft ad with an approximately 9 to 10 foot wooden Chris Craft Dingy. Would anyone be aware of where one could find plans to build a similar one?

Wanted, starboard (long) strut for a 1968 Chris Craft Commander 42. Or would anyone have a casting number. I called Algonac Cast Products Inc. With my number. They said that isn't there number. My number is 4961 4 and is stamped in.

This is for an ‘84 410 Starboard windshield actuator. I’m sure it could be many yrs and models.

The cover is very thin plastic(tan in color) and is 5x5x9 w/4 mounting screws

Earl @ Marine sales does NOT have the item.

Some of you may have made one out of wood and I’d like any ideas or drawings you may have for that possibly also.

Any help would be appreciated

Thanks

I am looking for rudders from a 1970s 47 commander. The information I have is that there were three generations of Rudders used on these boats. The first being the smallest, second medium, and the third the largest. I believe mine has the smallest and the performance as well as just looking at it me lead me to believe that it is way too small for this boat.

I have a 1979 410 commander and am in need of the rear most cabin windows. Eather salvaged ones or a source for replacement windows. Any help would be appreciated. Thank Frank

I am not sure what they are called and I cannot find them. Does anyone know if these are still available to buy?

They are the little chrome plated brass switch label bezel washer things as seen in the pic below.

Thanks for helping!

We are in search for our next boat; have likely narrowed down to the Commander Sport Fisherman; we are on Lake Erie and intend on bringing back on water; we have a 38' slip from our previous boat. Thanks

Looking for a swim platform for a 1971 Commander 38-

New or good used

Grand lake Oklahoma location

I'm looking for the sliding glass window track guide for our tourament 30 ?

Looking to replace my damaged heavy duty polished ss hull vents

my struts are in service but dezinctified looking for replacements for future

• 16 degree 1-1/4" prop shaft struts used on 

31ft ChrisCraft Commander,the 30ft Constellation, 30ft Cavalier Crusader and the 31ft Catalina

ChrisCraft part number 7460-4 and 7461-4

Looking for a pair of struts. Strut part numbers 7460-4 and 7461-4 . These were used on several model ChrisCrafts other than the Commander. 1-1/4" shafts . Send pictures of what you have with price. Thanks

I am looking to buy a Commander 42, 45 or 47. It must be mechanically and structurally excellent. I am prepared to update old cosmetics.